Use arrow keys, swipe, or choose any thumbnail.
2025 · Power Wagon
$68,072
MSRP $73,110
Listed as available at Livermore Subaru in Livermore, CA. Inventory last confirmed Aug 12, 2026. Contact the dealer to confirm current availability.
Browse more from Livermore Subaru on Autorrive →Autorrive Report
Here’s the official information available for this vehicle as of Aug 29, 2026. If a detail comes from a matching model or configuration rather than this specific vehicle, we’ll say so.
Vehicle specifications
Exact VIN decode
Matched year, make and model · not VIN-specific
0 NHTSA investigations found for this model year
305 communications found for this model year
These records can include service bulletins, repair instructions, campaigns, warranty extensions, software updates and other manufacturer notices. The total is not a problem rate or reliability score.
switch Electronic range select Before replacing the switch electronic gear selector 68379834AB due to P0826-29, P0826- 11 active codes, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps at BCM. 2.- If failure still present, make sure the switch is properly connected and there is no corrosion or pinching, disconnect the switch & reconnect it, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between gear selector switch and BCM. For example, try switching between driving modes. 4.- Read at the BCM diagnosis session if BCM is receiving information from gear selector. 5.- Do a hard reset to BCM and evaluate if any DTC or failure code is set. Retest if failure still present. If there are no DTC's, physical defects, gear selector inop, then the Electronic Gear Selector Switch does not need to be
SEAT BELT Front Outer Seatbelt Slow Retraction / Seat Belt Cleaning If the vehicle exhibits slow seatbelt retraction, prior to replacing seatbelt please inspect for debris and any build up on the webbing and DRing. If evidence of debris and build up, please clean seatbelt webbing or turning loop as described below. Seat Belt Maintenance: Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them. Dry with a soft cloth. Sun damage can also weaken the fabric. Replace the belts if they appear frayed or worn or if the buckles do not work properly. NOTE: If the belts retract slowly, inspect the upper turning loop for soiling. If soiling is present, clean with a wet soft cloth until all residue is removed.
SWITCH Headlamp Before replacing the Headlamp Switch for faulty dimmer operation. Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. 2.- Review the internal resistance of the switch: a.- For the Right Dimmer (IP) between Pins 6 & 3. The value should be around 5.74 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). b.- For the left Dimmer (Ambient Light) between pins 8 & 3. The value should be around 14.52 KOhms, when in the lowest position to 182 ohms in the top position. If a problem is found in the resistor values. Please replace the Switch.
Warranty Bulletin D-25-04 FFB Program - 6.7L Cummins Engine (Sales Codes ETM and ETN), Base Engine Comp, Electronic Comp, Cooling System Comp, Exhaust Gas Recirculation System, Fuel System and Aftertreatment System - Select 2025 2500/3500/4500/5500 Ram Pickup (DD/DJ/D2/DP)
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
CAMERA - REAR VIEW
Send your basic contact information now. Trade and financing details are optional on the next screen.