Document 11013266
ENGINE COOLANT SERVICE PROCEDURE SERVICE INFORMATION When draining and refilling the vehicles coolant for any reason, refer to the updated Electronic Service Manual (ESM) service procedure starting on page 2 of this bulletin to ensure that all air pockets have been completely purged. When refilling the cooling system, use Genuine Nissan BLUE LONG LIFE ANTIFREEZE or its equivalent, mixed with water that is distilled or demineralized. This amended procedure will be added to the ESM in a future update to the following ESM section: ENGINE > ENGINE COOLING SYSTEM > KR15DDT > PERIODIC MAINTENANCE > ENGINE COOLANT > Refilling IMPORTANT: The following information under step 5 on page 3 will be added to the ESM. If not using CONSULT, turn on cabin heater switch. Open the ENGINE COOLANT BYPASS VALVE by using CONSULT WORK SUPPORT function. o Refer to : ENGINE - ENGINE CONTROL SYSTEM - KR15DDT - SYS
Document 11013276
CRUISE CONTROL/PROPILOT STOPS WORKING IF YOU CONFIRM The customer states that while driving on an unobstructed road, and on a clear day without any rain, snow, or direct sunlight, the Cruise Control/ProPilot stopped working, AND The Automatic Emergency Braking/Forward Emergency Braking light (AEB/FEB) flashed while the Forward Driving Aids Disabled message was displayed in the combination meter, AND DTC C2582-97 for Distance sensor is stored as PAST. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current LASER/RADAR part number. 2. Reprogram the LASER/RADAR, if applicable. 3. Erase the DTCs. 4. Perform Distance Sensor Alignment. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this rep
Document 11013279
CHARGE AIR COOLER SYSTEMS SERVICE INFORMATION SERVICE INFORMATION If a body shop or dealer performs a repair affecting the charge air cooler (Figure 1), please be aware of the following information regarding the charge air cooler coolant refill procedure. IMPORTANT: If the charge air cooler coolant reservoir (Figure 2 on page 2) is not filled properly per details in this bulletin, spark plug and/or engine damage may occur. Figure 1
Document 11014075
MIL ON WITH DTC P0196 STORED IN THE ECM IF YOU CONFIRM The MIL is ON with DTC P0196 for EOT SENSOR stored in the ECM. HINT: DTC P0012 for INTAKE VALVE TIMING CONTROL B1 may be stored along with P0196 for EOT SENSOR. ACTION Follow the SERVICE PROCEDURE in this bulletin to diagnose DTC P0196 for EOT SENSOR. Disregard P0012 if stored along with P0196. Do not follow the service information in the ESM when diagnosing P0196. The ESM information will be updated at a later date.
Document 11024391
ACTION Date: October 2, 2025 To: FOMs, DOMs, RAMs, & RGMs Subject: LAUNCH PD172 PMA55 Multi Model Monroney Bumper Label QA Dealer Announcement and Procedure ACTION: FOMs & DOMs are asked to ensure that dealers are aware of this new campaign information. Dealer Announcement: To ensure continued customer satisfaction and confidence, Nissan is conducting a quality action on certain specific model year 2025 ARIYA, 2024-2025 Pathfinder, 2024-2026 Rogue, 2024-2025 Murano and 2025-2026 Kicks vehicles, as identified in Service Comm and DBS National Service History. This action updates the Monroney labels to reflect corrected bumper labeling requirements for California and Hawaii. Dealers will replace original Monroney labels with corrected Monroney labels. Nissan will send VIN-specific corrected labels to address affected vehicles in dealer inventory. New labels will begin shipping via Federal E
Document 11024395
STEERING WHEEL SWITCH BUTTONS INOPERATIVE, STICKING, OR NOT CLICKING WHEN PRESSED IF YOU CONFIRM The customer states that any of the steering wheel switch buttons are inoperative, sticking, or not clicking when pressed. ACTION Follow the SERVICE PROCEDURE to: 1. Remove the steering wheel assembly. 2. Replace the switch assembly on the steering wheel assembly. HINT: The switch assembly includes switches for both sides of the steering wheel. 3. Reinstall the steering wheel assembly. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.